Lasts
-
- 1
- Posts: 48
- Joined: Thu Jan 06, 2011 10:00 am
- Full Name: Chris Stratton
- Location: NY, NY
Re: Lasts
I wonder if the polycaprolactone plastic I'm using for lasts would stick to to the existing plastic of your last. It's a bit pricey for the whole last, but what's nice about it is you just get it hot (hot water or heat gun) and then bulldoze it around to whatever shape is of interest. Heat it back up if you don't like the result.
(Message edited by ccs on January 25, 2011)
(Message edited by ccs on January 25, 2011)
-
- 1
- Posts: 18
- Joined: Sun Jan 09, 2011 10:00 am
- Full Name: Mark Tucker
- Location: spickard, mo, usa
Re: Lasts
rick,
what type of apoxie are you using? And chris can you get me more info on the poly your using. thanks mark
what type of apoxie are you using? And chris can you get me more info on the poly your using. thanks mark
-
- 1
- Posts: 48
- Joined: Thu Jan 06, 2011 10:00 am
- Full Name: Chris Stratton
- Location: NY, NY
Re: Lasts
Apoxie sounds like it might be a filled epoxy?
Polycaprolactone is sold under many names. Cheapest in large quantity (8 lbs - not quite enough for two pairs of complete lasts, but easily 3 individuals plus some extra) is instamorph, in smaller quantities for additions friendly plastic, shapelock, polymorph plastic, etc. It does not glue well beyond its own tendency to adhere when hot though - would probably be most secure as an addition with some mechanical capture. Or you could drive a few wood screws part way in and mold it around the heads.
(Message edited by ccs on January 25, 2011)
Polycaprolactone is sold under many names. Cheapest in large quantity (8 lbs - not quite enough for two pairs of complete lasts, but easily 3 individuals plus some extra) is instamorph, in smaller quantities for additions friendly plastic, shapelock, polymorph plastic, etc. It does not glue well beyond its own tendency to adhere when hot though - would probably be most secure as an addition with some mechanical capture. Or you could drive a few wood screws part way in and mold it around the heads.
(Message edited by ccs on January 25, 2011)
- romango
- 8
- Posts: 854
- Joined: Wed Apr 18, 2007 1:40 pm
- Full Name: Rick Roman
- Location: Eugene, Oregon, USA
- Been Liked: 8 times
- Contact:
Re: Lasts
Apoxie Sculpt. I use it quite often and it works well on wood or plastic lasts. The only limitation is that it doesn't nail well. This is usually not a problem, I just have to set the nails slightly farther back when lasting.
- kevindeleon
- 1
- Posts: 19
- Joined: Mon Jan 02, 2012 10:33 pm
- Full Name: Kevin deLeon
- Location: New Orleans, LA, US
- Contact:
Re: Lasts
Anyone know if Allen is still the person to contact at JV? I'm just getting started in my adventure into custom shoe making, and trying to determine where to order my first pair of lasts.
- dw
- Seanchaidh
- Posts: 5830
- Joined: Wed Jan 01, 1997 10:00 am
- Full Name: DWFII
- Location: Redmond, OR
- Has Liked: 204 times
- Been Liked: 122 times
- Contact:
Re: Lasts
Allen is a good one to talk to but the go-to guy is Spencer Bruce...and you'll never talk to a more gentlemanly individual.
Tight Stitches
DWFII--HCC Member
[center]Little Jack Dandiprat in a white petticoat,
The longer he lives, the shorter he grows.[/center]
Tight Stitches
DWFII--HCC Member
[center]Little Jack Dandiprat in a white petticoat,
The longer he lives, the shorter he grows.[/center]
- kevindeleon
- 1
- Posts: 19
- Joined: Mon Jan 02, 2012 10:33 pm
- Full Name: Kevin deLeon
- Location: New Orleans, LA, US
- Contact:
- athan_chilton
- 4
- Posts: 163
- Joined: Sun May 17, 2009 7:03 am
- Full Name: Athan Chilton
- Location: Urbana, IL, USA
Re: Lasts
DW has beat me to it - so I'll just second what he's said. I just got two pr of lasts from J&V and dealt mostly with Spencer Bruce, indeed a most gentlemanly chap with a delicious semi-Southern way of speaking...what a change from rude, hasty sales people!!
-
- 6
- Posts: 469
- Joined: Mon Jan 29, 2007 10:00 am
- Full Name: Jesse Lee Cantrell
- Location: Town of Niagara, NY, USA
Re: Lasts
I have 3 pairs of plastic lasts I don't need.
10 1/2D- marked M824 on side. Barely used.
9C- marked Vulcan WR Oct 1980 and L-22
8B- marked the same. I can send pics to anyone who is interested.
Cheers,
JesseLee
10 1/2D- marked M824 on side. Barely used.
9C- marked Vulcan WR Oct 1980 and L-22
8B- marked the same. I can send pics to anyone who is interested.
Cheers,
JesseLee
- kevindeleon
- 1
- Posts: 19
- Joined: Mon Jan 02, 2012 10:33 pm
- Full Name: Kevin deLeon
- Location: New Orleans, LA, US
- Contact:
- kevindeleon
- 1
- Posts: 19
- Joined: Mon Jan 02, 2012 10:33 pm
- Full Name: Kevin deLeon
- Location: New Orleans, LA, US
- Contact:
Re: Lasts
Anyone have any experience with these guys?
Shoe Last Shop on eBay stores
Obviously they aren't custom, but might be good for people starting out? Still seems like JV might be the way to go considering you can send in measurements.
Shoe Last Shop on eBay stores
Obviously they aren't custom, but might be good for people starting out? Still seems like JV might be the way to go considering you can send in measurements.
- kemosabi
- 5
- Posts: 250
- Joined: Thu Jan 20, 2011 4:03 pm
- Full Name: Nat Ledbetter
- Location: Tennessee, USA
- Been Liked: 1 time
Re: Lasts
I've never heard of them. Looks like they're asking way too much for these lasts, since used production lasts can be had for $20.
If you're looking for a few pairs of lasts (vs. a whole run); it's hard to beat Panhandle Leather.
Cheers,
-Nat
If you're looking for a few pairs of lasts (vs. a whole run); it's hard to beat Panhandle Leather.
Cheers,
-Nat
- kevindeleon
- 1
- Posts: 19
- Joined: Mon Jan 02, 2012 10:33 pm
- Full Name: Kevin deLeon
- Location: New Orleans, LA, US
- Contact:
Re: Lasts
Nat,
Thanks so much. I looked on their site and didn't see anything in regards to lasts. Also, at this point I am mostly interested in shoe making, and it looks like they mostly deal in boot supplies (not to say there isn't any crossover). Do they shoe lasts as well?
Thanks so much. I looked on their site and didn't see anything in regards to lasts. Also, at this point I am mostly interested in shoe making, and it looks like they mostly deal in boot supplies (not to say there isn't any crossover). Do they shoe lasts as well?
- kemosabi
- 5
- Posts: 250
- Joined: Thu Jan 20, 2011 4:03 pm
- Full Name: Nat Ledbetter
- Location: Tennessee, USA
- Been Liked: 1 time
Re: Lasts
They have many things not listed on the website and I've found it works best to give them a call. Most of the lasts I've bought from them are shoe lasts. They prefer to call them "Roper Lasts", but they're actually shoe lasts (with curved heel vs. straight).
If you want to be really clear, you can ask for "5/8 heel, 5/8 toe spring". They'll know what this means.
-Nat
If you want to be really clear, you can ask for "5/8 heel, 5/8 toe spring". They'll know what this means.
-Nat
- kevindeleon
- 1
- Posts: 19
- Joined: Mon Jan 02, 2012 10:33 pm
- Full Name: Kevin deLeon
- Location: New Orleans, LA, US
- Contact:
-
- Posts: 2
- Joined: Fri Feb 03, 2012 4:21 pm
- Full Name: Daniel Petrzelka
- Location: Seattle / Skagit Valley, Washington, USA
Re: Lasts
Do any of you have experience with BootLast.com's model GC-400 developed by Greg Carmack.
I've read that their boot lasts are based on the work of the Krentler Brothers who seems be be quite highly regarded.
I've also noted that they've worked to create lasts with a more slender volume to support building up to fit (rather than grinding away) - as a totally new shoe maker I do not have experience with this yet, but find the approach of building upon the lines of the last makes the most intuitive sense.
I'm looking to make both low cut Chukka style boot, as well as dress style oxfords (my hope is to find a last that can be built upon for both if possible - and starting with the longer slender tow fits the style I have in mind)
Can anyone speak to hands on experience with the GC-400 lasts?
Images of shoes created on those lasts that you can share?
I've read that their boot lasts are based on the work of the Krentler Brothers who seems be be quite highly regarded.
I've also noted that they've worked to create lasts with a more slender volume to support building up to fit (rather than grinding away) - as a totally new shoe maker I do not have experience with this yet, but find the approach of building upon the lines of the last makes the most intuitive sense.
I'm looking to make both low cut Chukka style boot, as well as dress style oxfords (my hope is to find a last that can be built upon for both if possible - and starting with the longer slender tow fits the style I have in mind)
Can anyone speak to hands on experience with the GC-400 lasts?
Images of shoes created on those lasts that you can share?
- kevindeleon
- 1
- Posts: 19
- Joined: Mon Jan 02, 2012 10:33 pm
- Full Name: Kevin deLeon
- Location: New Orleans, LA, US
- Contact:
Re: Lasts
Daniel,
I was wondering if you heard anything regarding the GC-400 as I have also been interested in that last. It looks like a pretty versatile/modern shape. Would love to see some shoes made on it.
I was wondering if you heard anything regarding the GC-400 as I have also been interested in that last. It looks like a pretty versatile/modern shape. Would love to see some shoes made on it.
-
- Posts: 2
- Joined: Fri Feb 03, 2012 4:21 pm
- Full Name: Daniel Petrzelka
- Location: Seattle / Skagit Valley, Washington, USA
Re: Lasts
Jim - thank you for the feedback. Are there any photos on your website of boots you've made on the GC-200? ( Some beautiful work on your site, http://leatherfabrication.com/ )
Kevin, I'll keep you posted if I hear off-line from anyone specifically about the GC-400.
Kevin, I'll keep you posted if I hear off-line from anyone specifically about the GC-400.
-
- 1
- Posts: 12
- Joined: Sat Dec 18, 2010 10:00 am
- Full Name: Adam Jimenez
- Location: Winona, MN
Re: Lasts
message deleted...Reason:
(Message edited by admin on March 02, 2012)
The Crispin Colloquy is sponsored by The Honourable Cordwainers' Company--a 501, C-3, non-profit, tax-exempt, educational Trade Guild. As such, posts that solicit sales that may be construed as being for personal profit may not quote prices. The item may be described, its provenance detailed, and a contact address included. But, at risk of jeopardizing the tax-exempt status of the Guild, no prices may be quoted.
(Message edited by admin on March 02, 2012)